The Piping Inspector Certification Program (PICP) is developed for the continual high level of efficiency and safety through emphasizing professional credibility and process integrity. Process piping system is one of the critical production assets in process industry.
American Petroleum Institute (API) Piping Inspection Code 570 Inspection, Repair, Alteration, and Re rating of In
-Service Piping Systems is recognized and used with confidence worldwide.
The Piping Inspector Certification Program (PICP) is developed for the continual high level of efficiency and safety through emphasizing professional credibility and process integrity. Process piping system is one of the critical production assets in
process industry. Organizations recognize the need to maintain authorized inspection agency and technically assess qualified piping engineers and inspectors to ensure facilities are at top performance. Therefore, API 570 certification is one
of the most sought -after professional competency that enables inspectors to be actively involved in the improvement of industry & environmental health and safety performance, reinforcement management control, compliance with inspection capabilities. Each attendee must bring a laptop computer with Microsoft operating system.
By the end of this course, delegates will learn about:
• API 570: Inspection methodologies, remaining life calculations, degradation mechanisms, repair & re-rating of in-service piping system and relations to ASME codes (1.5 days)
• ASME Section V: Principles and Application of Non-Destructive
Examination (0.5 day)
• ASME section IX: Welding & brazing requirements and
procedures (0.5 day)
• ASME B31.3: Design review, welding & heat treatment, inspection,
leak testing of process piping (1 day)
• ASME B16.5: Design & repair of pipe flanges and flanged fittings (0.5 day)
• API RP 571: Damage Mechanisms affecting fixed equipment in refineries, e.g. fractures, fatigue, corrosion, sulfidation, MIC, HTTA etc. (0.5 day)
• API 574: Inspection practices for piping system components (¼day)
• API RP 577: Welding inspection and metallurgy recommended practices (¼ day)
• API RP 578: Material verification program for new and existing alloy piping systems (¼ day)
His 5-day Piping Inspector course is based on API 570/574, API RP 577/ 578, ASME B16.5/ B31.3 and ASME BPVC Section V/ Section IX. It is to promote the recognition of fitness-for-service concepts to evaluate in-service degradation of piping system. With our approved trainers’ extensive involvements in the facilities inspection, as well as the practical coaching and mentoring approaches, this course not only prepare the candidates to pass API 570 examination with confident, itwill also advance the appreciation of piping facilities and thus to broaden the technical knowledge base in order toavoid unplanned shutdown and reduce expenses!
This interactive Training will be highly interactive, with opportunities to advance your opinions and ideas and will include:
• Lectures
• Workshop & Work Presentation
• Case Studies and Practical Exercise
• Videos and General Discussions
Day 1
•BENCH-MARK QUIZ INTRODUCTION TO API 570 CERTIFICATION
•ASME B 31.3 (Process Piping)
•ASME B16.5 (Pipe Flanges and Flange Fittings)
Day 2
•ASME B16.5 (Pipe Flanges and Flanged Fittings)
•API 570 (Inspection, Repair, Alteration, and Rerating of In-Service Piping Systems)
Day 3
•API 570 (Inspection, Repair, Alteration, and Re rating of In-Service Piping Systems)
Day 4
•ASME Boiler and Pressure Vessel Code Section IX (Welding and brazing Qualifications)
•ASME Boiler and Pressure Vessel Code Section V (Non-Destructive Examination)
•API Recommended Practice 574
Day 5
•API RP 571 (Damage Mechanisms in the Refining Industry
4850 USD
Cairo, Bahrain, Dubai & Oman
5 Days
1st Feb 2024
Click to Check PDF
